Omrdon Technology 
金彩汇OMS-DIN/FM/0170, OMS-DIN/FF/0170 Antenna Lightning Protector for Broadcasting System, DIN(7/16) /L29 Antenna Lightning Protector, Female to Male, 1-70Mhz , 10KW,10kA, DC Pass
Product Description:
金彩汇 OMRDON DIN (7/16) type antenna lightning protector (SPD, surge protector) is suitable for broadcasting signal transmission, satellite TV receiving equipment and other various RF transceiver system lightning protection. Widely used in communication stations, radar stations, SmarTone base stations, mobile communication base stations, GPS base stations, CDMA base stations, PHS (PAS) base stations, satellite communications, microwave stations and so on. It can prevent damage to antenna and transceiver equipment caused by overvoltage of feeder-induced lightning strikes, and is installed in the lightning protection sub-district LPZ0A-1 and subsequent sub-districts.
The product is encapsulated in a shielded case with a built-in high quality high-speed overvoltage protection device, which provides efficient protection and defense against lightning high-voltage pulses induced on the antenna feeder line.
Functional Features::
- Lightning impulse current up to 20KA
- Maximum output power 10KW
- DC Pass
- Frequency range 1-70MHz
- Waterproof rating IP67
- DIN(7/16) /L29 type connector one male to one female (female to male)
- Very low VSWR <1.1
- Insertion loss <0.1dB
- International Certification RoHS, CE, FCC
typical application::
- GPS base station
- Broadcast base stations
- satellite communications
- radar base station
- microwave station
Technical Parameters
| model number | OMS-DIN/FM/0170 OMS-DIN/FF/0170 |
| Nominal discharge current (In) | 5 KA (8/20μs) |
| Maximum discharge current (Imax) | 10 KA (8/20μs) |
| Maximum RF power Pt | 10KWatts |
| VSWR | ≤1.1 |
| insertion loss | ≤0.1 dB |
| DC breakdown voltage (100V/s) | 3000 Volts |
| Maximum pulse voltage (1KV/μs) | 4200 Volts |
| characteristic impedance | 50Ω |
| frequency range | 1-70MHz |
| Reaction time (Ta) | ≤100 ns |
| Insulation impedance | ≥10GΩ |
| interface method | DIN(7/16) /L29 |
| Housing Material | Brass@Nickel Plated/Ternary Alloy |
| Ground resistance and wire diameter | ≤4Ω /≥6mm2 |
| sizes | FM@67.5*48mm, FF@63*48mm |
| Operating Temperature Range | -40 ~ +85℃,Altitude≤4km |
| Relative air humidity | 30%~90% |
| Protection class (IP) | IP67 |
| Compliance Certification | CE, RoHs,FCC,IP67 |
| Implementation standards | gb18802.21/lec61643-21/iec60169-4/iec60068-2-52 |
| item number | 8004261 8004262 |
Typical Performance Test Data
Simulated Lightning Impact Test
Product Dimension Drawing
Installation Notes:
1, in order to reliably prevent lightning strikes, can be in the antenna output and the input of the protected equipment are connected in series with an antenna feed lightning arrester the antenna feed lightning arrester is not divided into input and output, the interface can be matched.
2, the lightning protector on the lug welding as short as possible grounding wire (wire area of not less than 4mm) 2金彩汇), the other end is reliably connected to the lightning protection system grounding bus, and the grounding resistance is not more than 4Ω.
金彩汇3, the product has a waterproof function, but in the outdoor use of the antenna feeder should also pay attention to rain, do not let the rain soak into its internal corrosion damage.
4, this product does not require special maintenance. When the system works faulty, you can remove the lightning protector and then check, if the system returns to normal after restoring to the state before use, it means that the lightning protector has been damaged and must be replaced immediately.
